Films Protective Company is a manufacturer of PET and PE film materials for release liner, release-coated PET, adhesive-backed film, lamination film and precision converting applications. Before choosing between plain, treated, release-coated, or adhesive-backed PET, review PET plastic film properties and testing to compare mechanical, thermal, optical, and surface data under matched conditions. When a primer, release coating, adhesive layer, or laminate may change mechanical failure, review puncture testing for coated PET structures as a separate qualification step.This category supports procurement teams that need stable roll materials for labelstock, tape liner, graphic mounting and adhesive component production. Key selection points include controlled release, adhesive compatibility, roll flatness, surface readiness, clean unwinding and repeatable batch performance.
– Thickness: 12 um-250 um, coating-dependent
– Colors: clear, matte, white, translucent or tinted
– Materials: PET base film, PE-supported film, release-coated PET, adhesive-backed film
– Structures: plain film, release liner, single-side, double-side, differential release
– Supply: jumbo roll, slit roll, rewound roll, sheet, kiss-cut-ready roll
– Uses: labelstock, tape liner, mounting, lamination, adhesive transfer, precision converting
For projects centered on protecting printed graphics and display surfaces, the application guide explains how contact surface, dwell, handling, and removal requirements affect the material route.
Showing all 14 results
PET and PE film materials in this category are used as upstream converting materials before a finished label, tape, mounting film, adhesive transfer layer or precision-cut component is produced. The main specification question is whether the selected structure can pass through coating, laminating, slitting, rewinding or cutting equipment without release variation, curl, adhesive transfer or unstable waste removal.
PET base film is used for stiffness, dimensional stability and lower moisture-related curl. PE-supported or adhesive-backed structures are used when flexibility, bonding contact or lamination support is required. For coated or adhesive-ready grades, surface energy, silicone anchorage, coating-side identification and roll direction should be checked early because they affect bonding, liner removal and later converting stability.
PET identifies the base polymer, but it does not confirm orientation, coating, release level, surface treatment, or roll format. Review what PET film means and which specifications must still be confirmed before comparing the available film families.
Product Series | Covered Structure | Best-Fit Procurement Scenario |
PET base film | Clear, matte or treated PET | Coating, printing, lamination and carrier use |
PET release liner | Single-side or double-side release film | Labels, tapes, adhesive transfer and precision-cut parts |
Release-coated PET series | Easy, medium, tight or differential release grades | Controlled peel during unwinding, laminating and dispensing |
Adhesive-backed film | Removable, permanent or mounting adhesive structure | Graphic mounting, overlays and assembly films |
Lamination film series | PET-based or PET/PE-supported roll material | Film bonding, print protection and roll lamination |
Converting film rollstock | Slit roll, sheet or kiss-cut-ready structure | Industrial labels, adhesive parts and clean release work |
This grouping keeps the category at material-series level and avoids replacing the role of individual product pages. Equal-thickness rolls may run differently if release side, silicone anchorage, adhesive chemistry, liner stiffness, splice control or winding direction changes.
Selection Comparison | Recommended Choice | Key Checks |
Carrier vs release | PET base film for carrier use, release-coated film for adhesive separation | Coating side, release need |
Single-side vs double-side | Single-side for most PSA structures, double-side when both surfaces contact adhesive | Release side, unwind, blocking |
Easy vs tight release | Easy for dispensing, tighter for high-tack adhesive | Peel angle, peel speed, dwell time |
Silicone vs non-silicone | Silicone release for controlled peel, non-silicone when transfer risk is critical | Residual adhesion, silicone transfer |
Adhesive-backed vs lamination | Adhesive-backed for mounting, lamination film for bonding or protection | Tack, clarity, removal need |
Cutting vs laminating line | Low curl and clean edge for cutting, stable unwind for laminating | Roll flatness, web tension, core size |
Sample rolls should be tested close to the final process. Useful checks include peel testing at 23 C and 50% RH, residual adhesion review, silicone transfer observation, trial lamination, edge inspection and 24 hours or 72 hours dwell comparison. These checks help confirm whether the selected material series can move from trial roll to bulk use without unexpected converting issues. When polypropylene is also being considered for printing or lamination, compare treatment, COF, thermal shrinkage and barrier conditions rather than polymer names alone; see our OPP and PET film comparison for industrial converting.
When cleaners, process chemicals, or liquid contact are part of qualification, review the PET film chemical resistance technical data under matched concentration, temperature, exposure time, and film-construction conditions.
– Supports selection across PET base film, release liner, release-coated PET and adhesive-backed film.
– Helps reduce matrix lifting, adhesive legging, liner curl and poor waste removal.
– Matches release-force options with acrylic PSA, rubber-based adhesive, silicone PSA or removable adhesive.
– Improves equipment fit through roll flatness, slit width, core size, winding direction and web tension checks.
– Supports repeat purchases through retained samples, COA needs, lot comparison and packaging label control.
Before PET release liner enters label, tape or precision converting, approval should go beyond thickness and appearance. Confirm release force with the actual adhesive system, such as acrylic, rubber-based, silicone PSA or removable mounting adhesive. Roll flatness, liner curl, silicone transfer, residual adhesion, slit-edge cleanliness, web tension behavior and winding direction should be checked under the same lamination speed, cutting depth and storage condition used in production. A small mismatch may cause matrix lifting, adhesive legging, poor waste removal or unstable automatic dispensing.
Item | Typical Range / Customizable Value |
Film thickness | 12 um-250 um PET-based film, coated or adhesive structures confirmed by application |
Appearance | Clear, matte, white, translucent, tinted, anti-static or treated surface |
Surface and release | Surface energy, coating side, single-side, double-side, differential or non-silicone release |
Silicone anchorage | Rub test, tape lift review or agreed internal method before adhesive contact |
Release level | Easy, medium or tight release, confirmed by adhesive system and peel condition |
Adhesive options | Acrylic PSA, removable adhesive, permanent adhesive, mounting adhesive |
Roll format | Custom width, rewound or jumbo roll, 3 inch or 6 inch core |
Quality documents | TDS, COA, peel-test record, retained sample or lot inspection record |
Batch communication | Roll direction, label data, side marking, packing method, approved sample reference, moisture protection and lot traceability |
– PSA labelstock production where release force, matrix stripping and dispensing stability must stay controlled.
– Specialty adhesive material production, including double-sided tape, transfer tape and foam tape liner.
– Graphic mounting film for advertising panels, printed graphics and adhesive-backed overlays.
– Industrial converting where clean release, dimensional stability, low curl and low silicone transfer matter.
Films Protective Company can adjust PET and PE film materials by coating, laminating, slitting or cutting conditions. Adjustable items include PET base film thickness, release coating side, release-force grade, adhesive type, transparency, haze, matte finish, anti-static treatment, surface energy, silicone anchorage, roll width, roll length, core size and winding direction.
For adhesive-backed film, select adhesive by bonding surface, removal requirement, dwell time, temperature exposure, storage humidity and final converting method. For high-speed lines, check slit width tolerance, roll flatness, liner curl, splice control and waste stripping before bulk approval. For storage-sensitive structures, rolls should be protected from high humidity, direct sunlight and heavy compression, because poor storage may change curl behavior, release feel and unwinding stability before production.
Silicone coated PET should be selected when the film must carry, protect or transfer an adhesive layer without bonding permanently to it. Plain PET base film works as a stable carrier for coating, printing or lamination, but it does not provide controlled release. For labelstock, adhesive transfer film, graphic mounting film, tape liner and precision converting, the release surface helps the adhesive peel away during lamination, cutting, rewinding or dispensing. Match the release level to adhesive tack, coating weight, roll storage time, storage humidity and removal force.
Test release force with the actual adhesive, peel speed, application method and storage condition. Also check residual adhesion, silicone transfer and aging behavior.
Confirm thickness, release side, coating structure, release level, roll width, roll length, core size, winding direction, surface treatment and quality documents. For precision cutting, check slit-edge cleanliness, liner curl, roll flatness and splice control.
Bonding surface, dwell time, temperature, humidity, lamination pressure, cutting speed, dispensing method and equipment speed all affect selection. Confirm clarity, clean removal, adhesive anchorage and waste removal before approval.
MOQ should be discussed by structure, coating, adhesive, width and roll length. For repeat purchases, share the target release force, current sample or datasheet, expected quantity, roll direction, core size and packing method. Approved samples, COA or test report requirements, lot number and splice control should be kept as reference points.