No products were found matching your selection.

Other Related Products

  • Polyethylene Film Vapor Retarder: ASTM E1745 Technical Data

    This ASTM E1745 technical data explains how a polyethylene film vapor retarder should be reviewed below concrete slabs. It separates standard limits from typical references, lot-specific results, and project-confirmed values for thickness, water vapor permeance, tensile strength, puncture resistance, conditioned performance, and traceability. Final acceptance should use the submitted grade, current reports, and a representative mock-up under intended project conditions.

    Read moreDone

  • Refrigerator Adhesive Film

    • Material: PE film
    • Adhesive: acrylic pressure-sensitive adhesive
    • Common colors: clear, blue, milky white
    • Common thickness: 30–100 micron
    • Roll format: slit rolls, log rolls, jumbo rolls
    • Suitable surfaces: coated metal, stainless-look, plastic panels
    Read moreDone

  • Glossy Clear PET Film for Labels, Overlays and Lamination

    • Material: Clear BOPET / polyester
    • Surface: Glossy clear side
    • Thickness: 12-100 um
    • Common grades: 23 um, 36 um, 50 um
    • Format: Jumbo or slit rolls
    • Treatment: Corona or top-coated option
    Read moreDone

  • High Temperature Clear Plastic Film

    • Material: Clear PET backing with silicone adhesive
    • Color: Transparent clear
    • Heat Reference: Around 150 C short-term exposure
    • Test Option: 150 C / 30 min oven exposure
    • Adhesion: Low to medium tack
    • Format: Roll film with optional PET liner
    Read moreDone

  • Hot Melt Adhesive Film For Aluminum

    • Common thickness:20-300 um, ACP grades often 20-150 um
    • Available width:300-3000 mm, slit rolls for panel lamination lines
    • Resin options:EAA, EVA, PES, PO, and modified polyolefin
    • Color:Transparent, translucent, milky white, or resin-dependent
    • Structure:Glassine release paper or linerless roll format
    • Main use:Aluminum panel bonding, aluminum honeycomb, ACP, and profile lamination
    Read moreDone

  • Aluminum Panel Protective Film Application: Fabrication, Installation and Clean Removal

    An aluminum panel protective film application must keep the visible finish protected from lamination through fabrication, transport, installation and controlled removal. It is relevant to mill-finish, anodized, brushed, painted, powder-coated and coil-coated aluminum, including aluminum composite panels. The main risks are trapped particles, scratches, edge lift, film movement, difficult peeling, residue and coating appearance change. Selection should be based on the actual surface, coating condition, fabrication stress, expected exposure and removal stage—not thickness or tack alone—and should be confirmed through an actual-panel trial before full use.

    Read moreDone

  • a Pet Film For Thermoforming

    • Material: APET / thermoforming PET
    • Supply form: roll or sheet
    • Common thickness: 150–1200 μm
    • Color: clear, transparent, or custom tint
    • Surface: smooth, glossy forming surface
    • Main use: trays, blisters, clamshells, lids, inserts
    Read moreDone

  • Polyester Film Heat Stabilized

    • Material: Heat stabilized PET polyester film
    • Appearance: Clear or milky white available
    • Thickness Range: 50um-350um typical
    • Roll Format: Custom slit roll width
    • Surface: Untreated, one-side treated, or two-side treated
    • Main Use: FPC, printed electronics, insulation, coating, baking, lamination
    Read moreDone

  • PET Silicone Coated Release Film

    • Base film: clear PET liner
    • Thickness: 12-100 um
    • Width: slit or jumbo roll
    • Color: transparent or light translucent
    • Coating: silicone release layer
    • Use: tapes, labels, die-cut parts
    Read moreDone